[CSI] Community Software Installer 2.6.1 (OLD THREAD)

[Ger Teunis]

(12-23-2009 02:19 PM)dai_fuji Wrote:  http://IP:9091 not install,
http://IP:8077:
CSI my PC error:
help my!

Check your network settings. It seems that you PC isn't able to connect to your NMT at all. The daemon error can also occur when no connection is available at all. Please try to connect to the nmt via an ftp client first. If that works again try using transmission or csi again.

---

(12-23-2009 03:04 PM)michaelg04 Wrote:  ok, so i've had comcast for years, yesterday got AT&T Uverse installed and now community installer can't show my installed apps, it can install stuff, but can't see the installed apps. even from the web interface on the popcorn itself, well, from a browser on the pc to the popcorn i haven't tried the popcorn itself yet and can't until i get home tonight. any ideas on this?

it connects to it, i can also browse to it via my network, so unsure whats going on. IP is the same as well

What apps did you install just after it was still working?

[michaelg04]

nothing, all i have is nzbget, telnet and litepodder and csi app. it was working fine earlier in the day, then uverse came and now it doens't work. i put popcorn and pc back on old router and still having same issue, odd

i also cannot tenet into it anymore. i just set it up this week with a new 2tb drive, so it's a default install i have barely done anything accept move all my videos over

[Ger Teunis]

(12-23-2009 03:50 PM)michaelg04 Wrote:  nothing, all i have is nzbget, telnet and litepodder and csi app. it was working fine earlier in the day, then uverse came and now it doens't work. i put popcorn and pc back on old router and still having same issue, odd

i also cannot tenet into it anymore. i just set it up this week with a new 2tb drive, so it's a default install i have barely done anything accept move all my videos over

Does litepodder still work and nzbget on port 9999?
Seems something is broken for some reason.

[michaelg04]

i can get to nzbget webui sure, but it won't start, although that was an issue i had yesterday as well until i telnet in and change some permissions. and i'm not sure how to tell if litepodder is working, since i only have it setup for 1 podcast at the moment

[Ger Teunis]

(12-23-2009 04:09 PM)michaelg04 Wrote:  i can get to nzbget webui sure, but it won't start, although that was an issue i had yesterday as well until i telnet in and change some permissions. and i'm not sure how to tell if litepodder is working, since i only have it setup for 1 podcast at the moment

You have been tinkering with permissions?
I'd suggest reinstalling the nmt apps and start from scratch.
More info in first post in FAQ. You'll need a non-tinckered-with nmt.

[michaelg04]

only permissions i changes were on apps\nzbget, which supposedly needs to be done now since it seems broke. i guess i could do that, but i'm pretty sure it's related to this bogus uverse router

---

is it possible to reinstall the apps from the browser? as i'm at work remoting in to home pc

[michaelg04]

i'm pretty certain it has to do with the RG ATT Uverse router, and my dlink dir-825 i'm using as an access point. i can access the web gui for nzbget, but i get the can't connect error even though it's all setup right in the config, so something is blocking it through the network i'm thinking. maybe i'll set it up different later, use my netgear n router with ddwrt on it and put that in dmzplus. not sure, but it really is a pain in the butt, ATT should give u switches or something, nothing like leaving my home with half my stuff disconnected and i have to set it all up myself

[avanegmond]

(12-23-2009 06:37 PM)michaelg04 Wrote:  i'm pretty certain it has to do with the RG ATT Uverse router, and my dlink dir-825 i'm using as an access point. i can access the web gui for nzbget, but i get the can't connect error even though it's all setup right in the config, so something is blocking it through the network i'm thinking. maybe i'll set it up different later, use my netgear n router with ddwrt on it and put that in dmzplus. not sure, but it really is a pain in the butt, ATT should give u switches or something, nothing like leaving my home with half my stuff disconnected and i have to set it all up myself

Do I understand correctly you have two routers in your network now, i.e. RG ATT Uverse and DLink dir-825?
If so then that will definitely give problems!

Or is the router in your DLink switched off?

-
aleg

[Ger Teunis]

If users here get an empty installed application tab: please try uninstall lighttpd and report back if that solved your problem.
Some users seem to have issues after installing lighttpd.

[Ger Teunis]

Updated the stable to version 2.6.1
You'll get an update request automatically. If not: please redownload at http://www.nmtinstaller.com

New in this release
Issue 0000167: First start should not download the AB repository, just skip
Issue 0000168: Support Popcorn Hour C200 new firmware's ftp configuration
Issue 0000169: Add French translation to CSI as well as repository (thanks to Gregory Gauthier)

Merry christmas and happy new year!

[Ger Teunis]

.


THIS THREAD IS CLOSED, PLEASE GO TO THE NEW THREAD (part 2) NOW