New Usb drive problem, help !

[Brothan]

After years of using my A110 my internal 1tb hdd and my 1tb usb drive was starting to get full, I there for bought a new 2.5tb usb drive this weekend.. this was in NTFS format out of the box. I reformated it in to ext3 by conecting it to my Ubuntu workstation.. now the disk was excepted by the nmt started to move all my ISO:s to the new disk.... Got tired of the slow transfer so I connected all disks to the Ubuntu computer. Opened all rights an all disks and started transfering again.. this took 20 hours ..

Ok fine so I now have all my ISO:s on one disk and in alphabetic folders good .. only problem is that when i now try to connect the 2.5tb disk to the nmt I get USB-fault on every try... If i connect to the computer all is fine ... ??? Is there a way to solve this ?

[halfelite]

telnet into the a110 and run dmesg what is the full error.

[Brothan]

(07-07-2011 09:28 PM)halfelite Wrote:  telnet into the a110 and run dmesg what is the full error.

Ok, Thank you, I have used telnet before but i can't say i'm good at it.. how do I run the dmesg ? is this dmesg on the nmt or is it a program i have to transfer to the nmt ?

[halfelite]

use csi to install telnet. use putty or terminal on your ubuntu station type telnet pchip hit enter then connect the usb when it errors type dmesg hit enter.

[Brothan]

(07-08-2011 08:18 AM)halfelite Wrote:  use csi to install telnet. use putty or terminal on your ubuntu station type telnet pchip hit enter then connect the usb when it errors type dmesg hit enter.

Thanks, sounds simple, ill try this as soon I get home !

[Brothan]

This is part of what i got from the "log"

.
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
memory: 05ee0000 @ 10020000 (usable)
On node 0 totalpages: 89856
DMA zone: 89856 pages, LIFO batch:15
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line:
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 148.500 MHz high precision timer.
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 86400k/97152k available (3390k kernel code, 10652k reserved, 653k data, 3236k init, 0k highmem)
Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x15f00000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Created /proc/cpucache_info entry.
Installing knfsd (copyright © 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
SMP863x ir (254:0): driver loaded (wait_period = 200ms, buffer_size = 6)
SMP863x fip (253:0): driver loaded (buffer_size = 2)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
loop: loaded (max 8 devices)
tango2_enet: ethernet driver for SMP863x internal mac
tango2_enet: detected phy at address 0x01
tango2_enet: mac address 00:00:00:00:00:00
libata version 1.20 loaded.
physmap flash device CS2: 400000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
CS2: mymtds[cs]->size 2000000 f_sizes[cs] 400000
CS2: flash size mismatched, re-do probing/initialization.
physmap flash device CS2: 2000000 at 48000000 (remapped c8080000)
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
add_mtd_device first cs 2 es 020000 sz 2000000 esregion 1 000000 020000
Using physmap partition definition
MTD CS2-Part1 (offset:0x0, size:0x20000)
MTD CS2-Part2 (offset:0x20000, size:0x20000)
MTD CS2-Part3 (offset:0x40000, size:0x40000)
MTD CS2-Part4 (offset:0x80000, size:0x360000)
MTD CS2-Part5 (offset:0x3e0000, size:0x20000)
MTD CS2-Part6 (offset:0x0, size:0x0)
Adding partition #1-#6
Creating 6 MTD partitions on "CS2: Physically mapped flash":
0x01fe0000-0x02000000 : "Setting 1fe0000"
0x001e0000-0x01fe0000 : "Kernel 31457280"
0x009e0000-0x01fe0000 : "App 23068672"
0x00080000-0x01fe0000 : "Recover Kernel 32899072"
0x00040000-0x00080000 : "Yamon"
0x00000000-0x00040000 : "Zboot"
physmap flash device CS3: 4000000 at 4c000000
CFI: Found no CS3: Physically mapped flash device at location zero
driver tangox-ehci-hcd, 10 Dec 2004
TangoX USB initializing...
tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
TangoX USB was initialized.
Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 3236k freed
llad: module license 'LGPL' taints kernel.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...
hda: SAMSUNG HD103UJ, ATA DISK drive
hda: no 80 conductors cable, falling back to lower udma mode
hda: set to Ultra DMA mode 2
ide0: DMA enabled for ATA DISK hda
ide0 at 0x223c0-0x223c7,0x22398 on irq 26
hda: max request size: 128KiB
hda: 1953525168 sectors (1000204 MB) w/32767KiB Cache, CHS=65535/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3
tntfs: no version for "struct_module" found: kernel tainted.
Tuxera NTFS driver 3010.8.6 [Flags: R/W MODULE].
arusb - version 3.2.0.17
usbcore: registered new driver Otus
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
mumk_register_tasklet: (0) tasklet c800c000 status @ce424754
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
ext3_orphan_cleanup: deleting unreferenced inode 17446
EXT3-fs: hda1: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)
ir: Enable RC6 decoder
Algorithmics/MIPS FPU Emulator v1.5
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Vendor: WD Model: Ext HDD 1021 Rev: 2021
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
TNTFS error (device sda1, pid 878): read_ntfs_boot_sector(): Primary boot sector is invalid.
TNTFS error (device sda1, pid 878): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
TNTFS error (device sda1, pid 878): ntfs_fill_super(): Not an NTFS volume.
HFS+-fs: unable to find HFS+ superblock
attempt to access beyond end of device
sda1: rw=0, want=2441613320, limit=588806144
JBD: IO error reading journal superblock
EXT3-fs: error loading journal.
EXT2-fs: sda1: couldn't mount because of unsupported optional features (4).

any ideas anyone ??

[Brothan]

OK, had to do somthing about my problem so i managed to spread all my iso:s to a couple of smaller disk on my ubuntu station. Then i re-formated the 2.5tb disk and made sure that partitiontype was Linux and "type" was EXT3.. transfered all files again !! made a file system check this says file system good. Then I connect the disk to the PCH and it turns up as a unit !! Happy happy, but not for long when i try to access the disk I get to the folder in the root and when i try to get in to that one I get the message The request couldn't be done. ( This is how ever my direct translation from swe so it might not be correct )

I then try to change the permitions settings on the disk giving everybody full access, this doesen't help..

I then do the telnet trick I learn here and this is what I get:

Linux version 2.6.15-sigma (ctliew@xeon4x) (gcc version 4.0.4) #3267 PREEMPT Mon Mar 14 18:14:48 MYT 2011
Configured for SMP8634 (revision ES6/RevA), detected SMP8635 (revision ES9/RevC).
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
memory: 05ee0000 @ 10020000 (usable)
On node 0 totalpages: 89856
DMA zone: 89856 pages, LIFO batch:15
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line:
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 148.500 MHz high precision timer.
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 86400k/97152k available (3390k kernel code, 10652k reserved, 653k data, 3236k init, 0k highmem)
Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x15f00000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Created /proc/cpucache_info entry.
Installing knfsd (copyright © 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
SMP863x ir (254:0): driver loaded (wait_period = 200ms, buffer_size = 6)
SMP863x fip (253:0): driver loaded (buffer_size = 2)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
loop: loaded (max 8 devices)
tango2_enet: ethernet driver for SMP863x internal mac
tango2_enet: detected phy at address 0x01
tango2_enet: mac address 00:00:00:00:00:00
libata version 1.20 loaded.
physmap flash device CS2: 400000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
CS2: mymtds[cs]->size 2000000 f_sizes[cs] 400000
CS2: flash size mismatched, re-do probing/initialization.
physmap flash device CS2: 2000000 at 48000000 (remapped c8080000)
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
add_mtd_device first cs 2 es 020000 sz 2000000 esregion 1 000000 020000
Using physmap partition definition
MTD CS2-Part1 (offset:0x0, size:0x20000)
MTD CS2-Part2 (offset:0x20000, size:0x20000)
MTD CS2-Part3 (offset:0x40000, size:0x40000)
MTD CS2-Part4 (offset:0x80000, size:0x360000)
MTD CS2-Part5 (offset:0x3e0000, size:0x20000)
MTD CS2-Part6 (offset:0x0, size:0x0)
Adding partition #1-#6
Creating 6 MTD partitions on "CS2: Physically mapped flash":
0x01fe0000-0x02000000 : "Setting 1fe0000"
0x001e0000-0x01fe0000 : "Kernel 31457280"
0x009e0000-0x01fe0000 : "App 23068672"
0x00080000-0x01fe0000 : "Recover Kernel 32899072"
0x00040000-0x00080000 : "Yamon"
0x00000000-0x00040000 : "Zboot"
physmap flash device CS3: 4000000 at 4c000000
CFI: Found no CS3: Physically mapped flash device at location zero
driver tangox-ehci-hcd, 10 Dec 2004
TangoX USB initializing...
tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
TangoX USB was initialized.
Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 3236k freed
llad: module license 'LGPL' taints kernel.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide0: SMP863x/SMP865x Bus Mastering IDE controller
Probing IDE interface ide0...
hda: SAMSUNG HD103UJ, ATA DISK drive
hda: no 80 conductors cable, falling back to lower udma mode
hda: set to Ultra DMA mode 2
ide0: DMA enabled for ATA DISK hda
ide0 at 0x223c0-0x223c7,0x22398 on irq 26
hda: max request size: 128KiB
hda: 1953525168 sectors (1000204 MB) w/32767KiB Cache, CHS=65535/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3
tntfs: no version for "struct_module" found: kernel tainted.
Tuxera NTFS driver 3010.8.6 [Flags: R/W MODULE].
arusb - version 3.2.0.17
usbcore: registered new driver Otus
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
mumk_register_tasklet: (0) tasklet c800c000 status @ce424754
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
ext3_orphan_cleanup: deleting unreferenced inode 17477
EXT3-fs: hda1: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)
ir: Enable RC6 decoder
Algorithmics/MIPS FPU Emulator v1.5
usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 7 ports detected
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
usb 1-1.5: new high speed USB device using tangox-ehci-hcd and address 3
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: WD Model: Ext HDD 1021 Rev: 2021
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
TNTFS error (device sda1, pid 879): read_ntfs_boot_sector(): Primary boot sector is invalid.
TNTFS error (device sda1, pid 879): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
TNTFS error (device sda1, pid 879): ntfs_fill_super(): Not an NTFS volume.
HFS+-fs: unable to find HFS+ superblock
attempt to access beyond end of device
sda1: rw=0, want=2441613320, limit=588792200
JBD: IO error reading journal superblock
EXT3-fs: error loading journal.
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as ext2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
attempt to access beyond end of device
sda1: rw=0, want=2284584968, limit=588792200
EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=71393281, block=285573120
attempt to access beyond end of device
sda1: rw=0, want=2441613320, limit=588792200
JBD: IO error reading journal superblock
EXT3-fs: error loading journal.
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as ext2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
attempt to access beyond end of device
sda1: rw=0, want=2284584968, limit=588792200
EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=71393281, block=285573120
usb 1-1.5: USB disconnect, address 3
sd 0:0:0:0: rejecting I/O to device being removed
Buffer I/O error on device sda1, logical block 1025
lost page write due to I/O error on sda1
0:0:0:0: rejecting I/O to dead device
Buffer I/O error on device sda1, logical block 0
lost page write due to I/O error on sda1
usb 1-1.5: new high speed USB device using tangox-ehci-hcd and address 4
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: WD Model: Ext HDD 1021 Rev: 2021
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
SCSI device sda: 610471936 4096-byte hdwr sectors (301470 MB)
sda: assuming drive cache: write through
sda: sda1
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
TNTFS error (device sda1, pid 879): read_ntfs_boot_sector(): Primary boot sector is invalid.
TNTFS error (device sda1, pid 879): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
TNTFS error (device sda1, pid 879): ntfs_fill_super(): Not an NTFS volume.
HFS+-fs: unable to find HFS+ superblock
attempt to access beyond end of device
sda1: rw=0, want=2441613320, limit=588792200
JBD: IO error reading journal superblock
EXT3-fs: error loading journal.
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as ext2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
attempt to access beyond end of device
sda1: rw=0, want=2284584968, limit=588792200
EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=71393281, block=285573120
attempt to access beyond end of device
sda1: rw=0, want=2441613320, limit=588792200
JBD: IO error reading journal superblock
EXT3-fs: error loading journal.
EXT2-fs warning (device sda1): ext2_fill_super: mounting ext3 filesystem as ext2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
attempt to access beyond end of device
sda1: rw=0, want=2284584968, limit=588792200
EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=71393281, block=285573120


Please help...

[Brothan]

Anyone ? help ?

[Brothan]

I think i tried every format there is soon, im loosing my faith in this...

Is there any step by step guide how to format a usb disk to ext3 using ubuntu, get a little konfused by the talking of boot-disks in some threads ?

Have someone tried a 2.5tb disk before ?

[Brothan]

Hello, today I gave up my years with the A110 is over, she served me well until now.. Bought a new media player today..